Friday, 16 July 2021

Week 34 - The Build

 Here I am back again. Nearly a month since my last post. I've been away on my proper boat for awhile but came back to make tremendous progress on the project.

From the last post it can be seen that I'd trial fitted the belts, pulleys, clutch and shaft to drive the water jet. 

It was with some concern that the kit vendor now does not sell the kit that I bought, but only sells the hull with the major mechanical components already fitted as its too difficult for the likes of me! Bit of a worry, so most of this weekhas been spent in lining everything up so it worlks without the belts flying off or the clutch not engaging. To line up the pulleys I used a bit of steel bar. The predrilled holes for the drive shaft bearings seemed to be a bit in the wrong place and so were enlarged as required. 

So starting off with the belt from the pto to the drive shaft...

This is with the engine running at 4000rpm. Proper noisy, but nothing fell off!

Any way, and to cut to the chase here it is all assembled (aprt from the Mole grips) and in action.


and its all operated from this lever next to the handbrake 




Friday, 18 June 2021

Week 33 - The Build

 Well - lots of progress in the last few days!

The cooling system leak is fixed. There was a bit of aluminium pipe used to join two rubber hoses that was just a little bit too narrow. Replaced with a section of larger bore tube and all is well. There may be trouble ahead with the cooling system so perhaps more on this later!

The battery in the Fiesta wouldn't hold a charge and has been festering in my garage for ages. Thought I'd give it one last chance and use it anyway to see where the battery leads could best go. It seems to have recovered now and starts the car every time. Anyway, I've repainted inside the port bow section and installed the battery.

Here is the bay ready for the battery and box;

and with the battery in her box!

Next job was to instal the temperature gauge. The sensor unit was installed the the engine outlet hose...

whats a couple more jubilee clips!

and here is the gauge in action! It seems almost certain that the thermostat is either missing or stuck open. It's now almost inaccessible so it can stay stuck open for now!


Both the temperature gauge and the battery isolation switch will be mounted in the dashboard side extension pieces when the time comes.

So, the next exciting part is the trial fitting of the water jet drive components.

First job is to attach the pulley on the gearbox pto shaft, Straight away its obvious it wont fit on as the hull is in the way!

The black line shows what needs whittling away!

and here we are with the whittling complete and the pulley fitted.


Next bit is the belt and half the dog clutch...

Here it is from inside the engine room ...

and here from the wheel arch.

The previously mounted ECU is now in the way and so has to be moved.


 

 

Next is the shaft to the transfer box ..   here it is with the clutch disengaged...



and with the clutch engaged...


It can be seen that the shaft attached to the transfer box with a flexible joint and it's alignment is going to be ever so critical to ensure smooth operation. 

The last job here was to re-mount the ECU. Needed to make some brackets and here it is all neat and tidy and hopefully well away from flailing belts and pulleys.


Next big job is to line everything up!

Monday, 7 June 2021

Week 32 - The Build

 Another long week into the build and almost no progress! 

Key features are 

a) the cooling system only leaks when I'm not there. Could be that someone is emptying the header tank into the footwell when I'm not there. Possibly not as all the boys at Up To Scratch are honest hard workers who wouldn't play such a prank on the bosses Dad - probably.

b) I've installed a battery isolation switch in the cockpit. It will eventually be mounted on the left hand side of the dashboard. Here it is unmounted...


c) All the warning lights go out when the engine starts! Not sure why or how but last time I tried the abs, traction control and engine management lights stayed on which are MoT failures. (sometimes it makes more progress when I'm not there rather disappointingly)

Here is short video of it.. The only light that stays on is the 'engine room hatch open' warning light and thats because it's open!


So, the next two priority jobs are to seal the cooling system and get the brakes working.

Monday, 24 May 2021

Week 31 - The Build

 A quiet couple of weeks as I've been consumed by other things! But the good news is that I think I now have all the key parts required to complete the project. There is still a massive amount of work to be done but slowly and unsteadily I'm making progress. 

The main parts which I've been waiting for so long are the layshaft and dog clutch that connects the power take off to the water pump.

The clutch is made up of a drive shaft with a cv joint. The cup of the joint slides up and down on a splined shaft to engage or retract from the tripod. This is controlled by a lever on the end of a cable. This rather clumsy diagram endevours to show how the water jet is driven and controlled.

 


 This photo shows the shaft with the clutch disengaged....

 

..... and this one shows it engaged!!


Next week its to pick up on the issues arising from the test drive. Cooling system leak, wayward rear tracking and binding brakes.


Sunday, 9 May 2021

Week 30 - The Build


 Well. here you are. You wait a fortnight for a week then two come along at once!

Anyway, having got the radiator fan sorted out it's now time to get some water in the system to see what happens. A standard Fiesta should take 5.5l of coolant so I'd expect to be needing a fair bit more to fill the under hull tubes and the extended runs to the heater.I managed to get nearly 7l in before the header tank was full which didn't seem very much but time to run the engine. I've still got this strangeness of non starting unless initiated by the spraying of some flammable liquid into the air intake.

Just on tickover the engine warmed up very quickly and in fact nearly boiled before I turned it off. Either thed (new) water pump doesnt work, the thermostat is stuck shut or there is a massive air lock somewhere. The heater didn't get hot so hopefully an air lock. Lots of sqeezing and squishing of rubber hoses running it again with no improvment then going home while it all cooled down seemed to do the trick. The next day all seemed fine. The heater got hot and the radiator hoses got hot as well. If anything it didnt get hot enough which makes me now think that the thermostat is stuck open. Better than stuck shut but a problem for another day.

Next job is to put some wheels on and see if it starts and stops. 

The answer is here;


Really exciting time but every jar of ointment has it's fly. A number of flies in this case! The brakes are binding to a point where they are almost solid, the rear tracking is about 10 degrees out on one side, the handbrake cables foul the wheels and there is another water leak from the heater end of things. 


Week 29 - The Build

 The avid follower of this blog will now realise that some of my weeks are sometimes longer than seven days! This is mainly because I don't seem to make interesting progress all the time. This week's mantra has been 'Don't just do something - stand there!'

First job was to wire up the radiator fan as previously outlined. This all went well apart from it not working as expected. The main bit works ok in that the wire from the ignition switch to the relocated relay turns the fan on. The break in this wire that will accomodate the 'Off' switch turns it off. So far so good. The bit that didnt work is the 'Off' switch override. The plan was to take the the trigger from the original relay socket to close another relay that bypass the 'Off' switch.

Upon investigation it seem the terminal on the original relay socket which I supposed to be the trigger is always at 12v when the ignition is on. The terminal which I supposed was to earth is at 4.5v when the igition is on. Not enough for the relay to switch but perhaps when the engine runs hot this terminal drops to 0v and the relay switched and the fan comes on. 

Anyway I've replaced the original relay and used that output (that would have sent power directly to the fan) to trigger another relay that bypasses the 'Off' switch. 

Those of you that read the bit about my improving the cooling system with 27 jubilee clips will appreciate my using three relays instaed of one to turn the fan on. Fortunately I was able to saw off a couple of relays and holders from another Fiesta.It'll be fine - probably!

 Here is the relay by the fan


The relay by the fusebox that feeds off the original power cables

and the wires that will connect to the switch


All these wires and bits will all be tidied up after I've had the engine running up to temperature.

Next job is to fix the fan to the radiator. Again not so simples. The fan in the Fiesta goes behing the radiator. In Amfey it will go in front. This means that all the little brackets on the fan housing and radiator are useless. Some bracketry is required but here it is all fitted.







Tuesday, 27 April 2021

Week 28 - The Build

 As winter turns into Spring there is a lot more that can be done than working on the car! I've spent a certain amount of time on my proper boat even going away on it for a few days to avail myself of licensed premises in England while Welsh pubs are still shut.

All the big heavy jobs are now done so its now a matter of doing all the millions of little things that make finish it off.

I've started off by washing the areas in the fo'cstle that were contaminated with brake fluid and repainting them. 

The fuel tank and filler are now back in.

Something that needs to be addressed at some point is to fit and cable up the radiator cooling fan. The radiator is not going to be subjected to any great airflow either ashore or afloat. The fan needs to be arranged so it can be set to continuously on and this can easily be done by taking a feed from the ignition switch to the fan relay. The current plan is to move the relay to the back to avoid long runs of cable taking a high current and trigger this from the ignition. Plan A.1 is to have a switch in the trigger cable so it can be set to 'off'. Plan A.2 is to take a feed from the original relay trigger to override the 'off' switch. Should cover it!

No photos this week but a wiring diagram for the fan 




Week 57 - The Test

 Got all the paperwork off to register it as a car now to test it as a boat!! Here are a couple of videos and some photos of it in action......